Injection molding thermocouple configured for your mold and machine

Part quality on a molding machine is decided at a handful of measuring points, and an injection molding thermocouple has to report the temperature exactly where the heat matters. Therma has been making these probes by hand in Lindlar since 1991. Its quality management is certified to ISO 9001. Each delivery includes a test report at no extra cost.

In our B2B shop you set thermocouple type, sleeve or sheath, lead length and termination yourself, with the same configurator that runs across our entire range of thermocouples. Connectors, extension wire and compression fittings for each injection molding thermocouple can go into the same order. Standard configurations are largely stocked and typically ship after about a week. Your press therefore does not stand idle for long when a heating zone fails.

Our thermocouples for plastics processing also monitor granulate dryers, extruders and temperature control units, yet the mold remains the place where standard sizes most often fall short. Does your tool call for an unusual length, a reduced diameter or a special connection? Our engineers then build the injection molding thermocouple from a technical drawing or a STEP model. Lead time for such a custom build is usually one to two weeks.

Therma Refrenzen Kunden Clients Projekte Logos

Nozzle thermocouple for a stable melt temperature at the gate

The nozzle is the last heated point the melt passes, which makes it the place where an injection molding thermocouple matters most to many processors. Even a deviation of a few kelvin there alters viscosity and filling behavior, visible as short shots, sink marks or stringing at the gate. A nozzle thermocouple sits closest to this critical zone and gives the controller its most relevant signal.

Space around hot runner nozzles and manifolds is tight. Our sheathed thermocouples bend around heater bands and slip into narrow grooves, while their mineral insulation withstands constant heating cycles. With an Inconel 600 sheath, the miniature type K versions start at 0.5 mm. Thin probes react quickly but tolerate less mechanical stress. On machine nozzles that see frequent tool changes, a slightly heavier sheath often lasts longer, so a plastic injection thermocouple is a wear part worth keeping in stock. Where one manifold feeds several cavities, each nozzle usually has its own control zone. We build every injection molding thermocouple for such a tool to identical length and lead. Readings stay comparable, so the controller can balance the cavities evenly.

Adapting the injection mold thermocouple to bore depth and diameter

For an injection molding thermocouple in the tool itself, measuring mold temperature means measuring inside steel. The probe goes into a blind hole drilled close to the cavity, where its tip has to touch the bottom. If a thin air gap remains at the tip, the reading drops and the response slows.

That is why the classic injection mold thermocouple is a plug-in design. Our plug-in thermocouples carry the measuring junction inside a brass sleeve. A spring on the lead pushes the sleeve onto the bottom of the bore, and a locking cap on the mounting adapter holds that pressure. Because the spring absorbs thermal expansion and vibration, contact remains stable throughout production.

To configure an injection molding thermocouple for your mold, we need three dimensions: bore diameter, bore depth and the distance from the mold surface to the connector. Sleeve size, spring length and lead are then matched to your tool. Since the usable temperature range depends mainly on the lead insulation, a fiberglass lead is the safer choice on hot molds than PTFE or silicone.

Sheath material and diameter as levers for a faster response time

The less mass the heat has to warm at the tip, the faster a probe follows a temperature change. A 1 mm sheath therefore reacts noticeably quicker than a 3 mm one, while the heavier version copes better with abrasion and rough handling during mold changes. Choosing the diameter of a thermocouple for injection molding is always a trade-off between speed and service life.

Stainless steel is sufficient as sheath material for the melt of most common thermoplastics, which stays roughly in the range from 150 to 400 °C. Inconel comes in when temperatures climb further, as with high-performance polymers, or when aggressive additives attack the sheath.

Which type does your controller expect? Check this before you order a replacement injection molding thermocouple. Most plastics machinery works with type J in Fe-CuNi or type K in NiCr-Ni. Older German machines are often set up for type L. It uses the same metals as type J but follows a different characteristic curve, so the two cannot be swapped.

Where the injection molding thermocouple is a type J thermocouple, the lead up to the controller input has to be type J thermocouple wire as well. Any copper section in between falsifies the reading without a visible fault.

Replacement probes for existing molds reproduced from your sample

Molds often run for many years, while the original sensor data sheet gets lost along the way. Even a failed probe still tells us what we need. We identify its thermocouple type first, then take sleeve, spring and lead dimensions directly from the part on our bench. The injection molding thermocouple you receive back fits the existing bore and controller without any adjustment.

Spare probes pay off on multi-cavity molds. Keeping a few of identical build on the shelf shortens an unplanned stop considerably, especially when one tool carries a dozen heating zones or more. Send us the old probe or a photo with the key dimensions, and a quotation follows. Questions about a specific injection molding thermocouple can be settled directly with our engineering team, whose line is +49 2266 487330-30.