Here you are: Home / Products / Thermo connectors / Standard connectors

Standard connectors

Connector Standards

  • Connector Standard (CSP-CSJ)

    • Use:
    Plug connector for thermocouple and RTD circuits. The solid connector pins guarantee reliable connection under even the most difficult conditions.

    Mechanical design:
    • Housing of fibreglass-filled plastic.
    • Contacts of original thermocouple materials.
    • Solid connector pins and spring-loaded socket.
    • Reverse polarity protection by different pin thicknesses.
    • Central cover attachment for fast installation.
    • Moulded barriers prevent short-circuits.
    • Screw terminals enable quick connection.

    Conductor diameter:
    • Reliable connection from 0.2 mm to 2.0 mm diameter.
    • Max. cable diameter 8.0 mm.

    Temperature load:
    • Max. 200 °C.

    Colour designations:
    • All international colour designations are available:
      DIN IEC, DIN 43710, ANSI, NFE, BS, JIS, etc.

    Accessories:
    Article number:
    • Connector plug: CSP-XX – last two characters ‘XX’ see table.
    • Coupling jack: – CSJ-XX – Example: CSP-KI = Connector Standard Type “K”, green.

  • Connector Standard Ceramic (CSPC-CSJC)

    • Use:
    Connector for thermocouple and RTD circuits. The solid connector pins guarantee reliable connection under even the most difficult conditions. The sheath pin contacts enable economical pricing.

    Mechanical design:
    • Ceramic housing.
    • Contacts of original thermocouple materials.
    • Solid connector pins and spring-loaded socket.
    • Reverse polarity protection by different pin thicknesses.
    • Moulded barriers prevent short-circuits.
    • Screw terminals enable quick connection.

    Conductor diameter:
    • Reliable connection from 0.2 mm to 2.0 mm diameter.
    • Max. cable diameter 7.0 mm.

    Temperature load:
    • Max. 650 °C.

    Colour designations:
    • White housing with colour dot as designation.

    Accessories:
    Article number:
    • Connector plug: CSPC-XX – last two characters ‘XX’ see table.
    • Coupling jack: – CSJC-XX – Example: CSPC-KI = Connector Standard Ceramic Type “K”, green.

  • Connector Standard Duplex (CSPD-CSJD)

    • Use:
    Connector for thermocouple and RTD circuits. The solid connector pins guarantee reliable connection under even the most difficult conditions.

    Mechanical design:
    • Housing of fibreglass-filled plastic.
    • Contacts of original thermocouple materials.
    • Solid connector pins and spring-loaded socket.
    • Reverse polarity protection by different pin thicknesses.
    • Central cover attachment for fast installation.
    • Moulded barriers prevent short-circuits.
    • Screw terminals enable quick connection.

    Conductor diameter:
    • Reliable connection from 0.2 mm to 2.0 mm diameter.
    • Max. cable diameter 8.0 mm. .

    Temperature load:
    • Max. 200 °C.

    Colour designations:
    • The housing colour is white and the thermo-pairing is imprinted.
    • Colour dot as special version at extra price.

    Accessories:
    Article number:
    • Connector plug: CSPD-XX – last two characters ‘XX’  see table.
    • Coupling jack: CSJD-XX – Example: CSPD-KI = Connector Standard Duplex Type “K”, green.

  • Connector Standard High-temperature (CSPH-CSJH)

    • Use:
    Plug connector for thermocouple and RTD circuits. The solid connector pins guarantee reliable connection under even the most difficult conditions. The special plastic used allows high working temperatures. The sheath pin contacts enable economical pricing.

    Mechanical design:
    • Housing of fibreglass-filled plastic.
    • Contacts of original thermocouple materials.
    • Solid connector pins and spring-loaded socket.
    • Reverse polarity protection by different pin thicknesses.
    • Central cover attachment for fast installation.
    • Moulded barriers prevent short-circuits.
    • Screw terminals enable quick connection.

    Conductor diameter:
    • Reliable connection from 0.2 mm to 2.0 mm diameter.
    • Max. cable diameter 8.0 mm.

    Temperature load:
    • Max. 350 °C.

    Colour designations:
    • The housing colour is brown and the thermo-pairing is imprinted.
    • Colour dot as special version at extra price.

    Accessories:
    Article number:
    • Connector plug: CSPH-XX – last two characters ‘XX’ see table.
    • Coupling jack: CSJH-XX – Example: CSPH-K = Connector Standard High-temperature, Type “K”.

  • Connector Standard Jab-in (CSPQ-CSJQ)

    • Use:
    Connector for thermocouple and RTD circuits. The solid connector pins guarantee reliable connection under even the most difficult conditions. Jab-in cover allow easy connection without need cover removal.

    Mechanical design:
    • Housing of fibreglass-filled plastic.
    • Contacts of original thermocouple materials.
    • Reverse polarity protection by different pin thicknesses.
    • Central cover attachment for fast installation.
    • Moulded barriers prevent short-circuits.
    • Screw terminals enable quick connection.

    Conductor diameter:
    • Reliable connection from 0.2 mm to 2.0 mm diameter.

    Temperature load:
    • Max. 200 °C.

    Colour designations:
    • All international colour designations are available:
      DIN IEC, DIN 43710, ANSI, NFE, BS, JIS, etc.

    Accessories:
    Article number:
    • Connector plug: CSPQ-XX – last two characters ‘XX’ see table.
    • Coupling jack: CSJQ-XX – Example: CSPQ-KI = Connector Standard Jab-in Type “K”, green.

  • Connector Standard Three-pin (CSPT-CSJT)

    • Use:
    Connector for thermocouple and RTD circuits. The solid connector pins guarantee reliable connection under even the most difficult conditions. The third contact for ground or continuous shield or for three wire RTD´s.

    Mechanical design:
    • Housing of fibreglass-filled plastic.
    • Contacts of original thermocouple materials.
    • Solid connector pins and spring-loaded socket.
    • Reverse polarity protection by different pin thicknesses.
    • Central cover attachment for fast installation.
    • Moulded barriers prevent short-circuits.
    • Screw terminals enable quick connection.

    Conductor diameter:
    • Reliable connection from 0.2 mm to 2.0 mm diameter.
    • Max. cable diameter 8.0 mm. .

    Temperature load:
    • Max. 200 °C.

    Colour designations:
    • All international colour designations are available:
      DIN IEC, DIN 43710, ANSI, NFE, BS, JIS, etc.

    Accessories:
    Article number:
    • Connector plug: CSPT-XX – last two characters ‘XX’ see table.
    • Coupling jack: CSJT-XX – Example: CSPT-KI = Connector Standard Three-pin Type “K”, green.

  • Multiple Jack Standard (MJS)

    • Use:
    Multiple Jack for thermocouple and RTD circuits. Suitable for connecting up to 6 standard circuits simultaneously.

    Mechanical design:
    • Strong steel plate housing, coated with epoxy resin.
    • Anodised aluminium handle for easy disconnection of the plug connectors.
    • Available with contacts for 1 to 6 measurement circuits.
    • Incorporates a standard vertical panel, Type “PAV-(...)” .

    Conductor diameter:
    • Reliable connection from 0.2 mm to 2.0 mm diameter.
    • Cable inlet screw fitting PG13 for cable diameter up to 15 mm.

    Temperature load:
    • Max. 200 °C.

    Colour designations:
    • All international colour designations are available.

    Article number:

  • Multiple Plug Standard (MPS)

    • Use:
    Multiple connectors for thermocouple and RTD circuits. Suitable for direct connection of up to 6 circuits simultaneously.

    Mechanical design:
    • Strong steel plate housing, coated with epoxy resin.
    • Anodised aluminium handle for easy disconnection of the plug connectors.
    • Available with contacts for 1 to 6 measurement circuits.
    • Corresponds with Standard Vertical Panel Type “PASV-(...)” and Sandard Multiple Jack Type “MJS-(...)”.

    Conductor diameter:
    • Reliable connection from 0.2 mm to 1.5 mm diameter...
    • Cable inlet screw fitting PG13 for cable diameter up to 15 mm.

    Temperature load:
    • Max. 200 °C.

    Colour designations:
    • All international colour designations are available.

    Article number:

Panel Standard Insert

  • Panes Standard Insert (PSI)

    • Use:
    Panel insert for thermocouple and RTD circuits. Designed to used together with panel sets for assembly to complete standard panels.

    Mechanical design:
    • Housing of fibreglass-filled plastic.
    • Contacts of original thermocouple materials.
    • Spring-loaded sockets.
    • Reverse polarity protection by different pin thicknesses.
    • Moulded barriers prevent short-circuits.
    • Screw terminals enable quick connection.
    • Polarity designation next to the connection screws.

    Conductor diameter:
    • Reliable connection from 0.2 mm to 2.0 mm diameter.

    Temperature load:
    • Max. 200 °C.

    Colour designations:
    • All international colour designations are available:
      DIN IEC, DIN 43710, ANSI, NFE, BS, JIS, etc.

    Accessories:
    • The standard built-in couplings are combined with the corresponding kits with front plate and installation set. See separate data sheet.

    Article number:
    • PSI-XX – last two characters ‘XX’ see table.
    • Example: PSI-KI = Panes Standard Insert Type “K”, green.

  • Panel Standard Insert Flanged (PSIF)

    • Use:
    Panel insert for thermocouple and RTD citcuits. Mounting by means of a stainless steel bracket and two screws.

    Mechanical design:
    • Housing of fibreglass-filled plastic.
    • Contacts of original thermo-element materials.
    • Spring-loaded sockets.
    • Reverse polarity protection by different pin thicknesses.
    • Conductor guides for prevention of short-circuits.
    • Screw terminals enable quick connection.
    • Polarity designation next to the connection screws.

    Conductor diameter:
    • Reliable connection from 0.2 mm to 2.0 mm diameter.

    Temperature load:
    • Max. 200 °C.

    Colour designations:
    • All international colour designations are available:
      DIN IEC, DIN 43710, ANSI, NFE, BS, JIS, etc.

    Article number:
    • PSIF-XX – last two characters ‘XX’ see table.
    • Example: PSIF-KI = Panel Standard Insert Flanged Type “K”, green.

  • Panel Standard Insert Flanged Bracket Mounting (PSIFB)

    • Application: :
    Panel insert for thermocouple and RTD citcuits. Mounting by means of a stainless steel bracket and two screws.

    Mechanical design:
    • Housing of fibreglass-filled plastic.
    • Contacts of original thermocouple materials.
    • Spring-loaded sockets.
    • Reverse polarity protection by different pin thicknesses.
    • Moulded barriers prevent short-circuits.
    • Screw terminals enable quick connection.
    • Polarity designation next to the connection screws.

    Conductor diameter:
    • Reliable connection from 0.2 mm to 2.0 mm diameter.

    Temperature load:
    • Max. 200 °C.

    Colour designations:
    • All international colour designations are available:
      DIN IEC, DIN 43710, ANSI, NFE, BS, JIS, etc.

    Article number:
    • PSIFB-XX – last two characters ‘XX’ see table.
    • Example: PSIFB-KI = Panel Standard Insert Flanged Bracket Mounting Type “K” green.

  • Panel Standard Insert High-temperature (PSIH)

    • Application:
    Panel insert for thermocouple and RTD circuits. Specially designed to be used together with the high temperature stainless steel panels.

    Mechanical design:
    • Housing of fibreglass-filled plastic.
    • Contacts of original thermcouple materials.
    • Spring-loaded sockets.
    • Reverse polarity protection by different pin thicknesses.
    • Moulded barriers prevent short-circuits.
    • Screw terminals enable quick connection.
    • Polarity designation next to the connection screws.

    Conductor diameter:
    • Reliable connection from 0.2 mm to 2.0 mm diameter.

    Temperature load:
    • Max. 350 °C.

    Colour designations:
    • The housing colour is brown with a colour dot.

    Article number:
    • PSIH-XX – last two characters ‘XX’ see table.
    • Example: PSIH-KI = Panel Standard Insert High-temperature Type “K”, green.

  • Panel Standard Insert Lugged (PSIL)

    • Use:
    Single built-in couplings for installation in front plates, housings, etc.
    Attachment with two screws M3.

    Mechanical design:
    • Housing of fibreglass-filled plastic.
    • Contacts of original thermocouple materials.
    • Spring-loaded sockets.
    • Reverse polarity protection by different pin thicknesses.
    • Central cover attachment for fast installation.
    • Moulded barriers prevent short-circuits.
    • Screw terminals enable quick connection.
    • Polarity designation next to the connection screws.

    Conductor diameter:
    • Reliable connection from 0.2 mm to 2.0 mm diameter.
    • Max. cabel diameter 8.0 mm.

    Temperature load:
    • Max. 200 °C.

    Colour designations:
    • All international colour designations are available:
      DIN IEC, DIN 43710, ANSI, NFE, BS, JIS, etc.

    Accessories:
    Article number:
    • PSIL-XX – last two characters ‘XX’ see table.
    • Example: PSIL-KI = Panel Standard Insert Lugged Type “K”, green.

  • Standard direct built-in coupling (PSIR)

    • Use:
    Single built-in couplings for direct assembly with panels
    in round panel apertures with a diameter of 27 mm.

    Mechanical design:
    • Housing of fibreglass-filled plastic.
    • Contacts of original thermocouple materials.
    • Spring-loaded sockets.
    • Reverse polarity protection by different pin thicknesses.
    • Polarity designation on the housing.
    • Front side installation with two screws

    Conductor diameter:
    • Reliable connection from 0.2 mm to 2.0 mm diameter.

    Temperature load:
    • Max. 200 °C.

    Colour designations:
    • ANSI colour designation ex-stock.
      All international colour designations are available.

    Article number:

  • Panel Standard Insert Three-pin High-temperature (PSITH)

    • Use:
    Panel insert for thermocouple and RTD circuits. For assembly with panel kits into complete high temperature standard stainless steel panels. The special plastic used allows high working temperatures. Third connection for ground or continuous shield connection or for three wire RTD´s.

    Mechanical design:
    • Housing of fibreglass-filled plastic.
    • Contacts of original thermocouple materials
    • Spring-loaded sockets.
    • Reverse polarity protection by different pin thicknesses.
    • Moulded barriers prevent short-circuits.
    • Screw terminals enable quick connection.
    • Polarity designation next to the connection screws.

    Conductor diameter:
    • Reliable connection from 0.2 mm to 2.0 mm diameter.

    Temperature load:
    • Max. 350 °C.

    Colour designations:
    • The housing colour is black with a colour dot.

    Article number:
    • PSITH-XX – last two characters ‘XX’ see table.
    • Example: PSITH-KI = Panel Standard Insert Three-pin High-temperature Type "K", green.

  • Panel Standard Insert Three-pin Lugged (PSITL)

    • Use:
    Panel insert for thermocouple and RTD circuits. Third connection for ground or continuous shield or for three wire RTD´s. Can be mounted in a single circuit version or in rows in customer panel. Mounting by means of two M3 screws.

    Mechanical design:
    • Housing of fibreglass-filled plastic.
    • Contacts of original thermocouple materials.
    • Spring-loaded sockets.
    • Reverse polarity protection by different pin thicknesses.
    • Moulded barriers prevent short-circuits.
    • Central cover attachment for fast installation.
    • Screw terminals enable quick connection.

    Conductor diameter:
    • Reliable connection from 0.2 mm to 2.0 mm diameter.
    • Max. cable diameter 8.0 mm.

    Temperature load:
    • Max. 200 °C.

    Colour designations:
    • All international colour designations are available:
      DIN IEC, DIN 43710, ANSI, NFE, BS, JIS, etc.

    Accessories:
    Article number:
    • PSITL-XX – last two characters ‘XX’ see table.
    • Example: PSITL-KI = Panel Standard Insert Three Pin Lugged Type “K”, green.

Panel Standard

  • Connector Standard Panel Bracket

    • Use:
    Installation clamp for standard, ceramic or high-temperature connector for panel installation.

    Mechanical design:
    • All parts, including the screws, are made of stainless steel.

    Order no.:
    • A-20.209 Clamp for ceramic connector.
    • A-20.306 Clamp for standard or high-temperature connector.

  • Panel Assembly Standard Horizontal (PASH)

    • Use:
    Panel assembly for thermocouples and RTD circuits for mounting in control rooms, test stands, laboratory applications, pilot plans, etc.

    Mechanical design:
    This panel consist of the panel set BM 20.059-x fitted with the standard panel inserts PSI-(...) , For further details see separate specification sheets.

    Conductor diameter:
    • Reliable connection from 0.2 mm to 2.0 mm diameter.

    Temperature load:
    • Max. 200 °C.

    Article number:
    • PAS-x-yz:
      x = number of circuits – 1, 2, 3, 4, 5, 6, 8, 12, 18, 24
      y = calibration – E, J, K, N, T, U, R/S, C, B
      z = colour code standard – I = IEC, A = ANSI, D = DIN, J = JIS
      see table.

  • Panel Assembly Standard Vertical (PASV)

    • Use:
    Panel assembly for thermocouples and RTD circuits for mounting in control rooms, test stands, laboratory applications, pilot plans, etc.

    Mechanical design:
    • Aluminium front plate, anodised, protected against corrosion.
    • Measurement circuit numbering, abrasion- and wipe-proof.
    • Attachments of stainless steel and nickel-plated brass.
    • The assembly type and design prevent the fitted built-in couplings
      from being pushed in or out.
    • The bevelled connection levels enable easy connection and
      disconnection of the conductors in the installed condition.
    • Individual panel insert can be replaced by loosening only a few screws.
    • Standard panels for 1 to 6 measurement circuits.

    Conductor diameter:
    • Reliable connection from 0.2 mm to 2.0 mm diameter.

    Temperature load:
    • Max. 200 °C.

    Article number:
    • PAS-x-yz:
      x = number of circuits – 1, 2, 3, 4, 5, 6
      y = calibration – E, J, K, N, T, U, R/S, C, B
      z = colour code standard – I = IEC, A = ANSI, D = DIN, J = JIS
      see table.

  • Panel Assembly Standard High-temperature (PASVH)

    • Use:
    Panel assembly for thermocouples and RTD circuits for mounting in control rooms, test stands, laboratory applications, pilot plans, etc.

    Mechanical design:
    • Stainless steel, corrosion-proof.
    • Attachments of stainless steel.
    • The assembly type and design prevent the fitted with the standard high temperature panel insert PSIH-(...) from being pushed in or out.
    • The bevelled connection levels enable easy connection and disconnection of the conductors in the installed condition.
    • Standard panels for 6 measurement circuits.

    Conductor diameter:
    • Reliable connection from 0.2 mm to 2.0 mm.

    Temperature load:
    • Max. 350 °C.

    Article number:
    • PASVH-x-yz:
      x = number of circuits – 1, 2, 3, 4, 5, 6
      y = calibration – E, J, K, N, T, U, R/S, C, B
      z = colour code standard – I = IEC, A = ANSI, D = DIN, J = JIS
      see table.

     

  • Panel Assembly Standard Vertical Three-pin High-temperature (PASVTH)

    • Use:
    Panel assembly for thermocouples and RTD circuits for mounting in control rooms, test stands, laboratory applications, pilot plans, etc.

    Mechanical design:
    • Stainless steel, corrosion-proof.
    • Attachments of stainless steel.
    • The assembly type and design prevent the fitted built-in couplings from being pushed in or out.
    • The bevelled connection levels enable easy connection and
      disconnection of the conductors in the installed condition.
    • Standard panels for 6 measurement circuits.

    Conductor diameter:
    • Reliable connection from 0.2 mm to 2.0 mm diameter.

    Temperature load:
    • Max. 350 °C.

    Article number:
    • PASVH-x-yz:
      x = number of circuits – 1, 2, 3, 4, 5, 6
      y = calibration – E, J, K, N, T, U, R/S, C, B
      z = colour code standard – I = IEC, A = ANSI, D = DIN, J = JIS
      see table.

     

Accessoires Standard

  • Crimp-insert

    • Application:
    Crimp-insert can be fitted in the entrance hole of the connector. Designed for soldering or crimping on mineral insulated metal sheathed cable or crimping on insulated wire.

    Construction:
    • Brass machined insert with 0,1 mm tolerance on the cable O.D. The adapter fits in all standard connectors.

    Order no.   –   Dimension A (mm)  / Dimension B (mm)
    • A-20.025-1   –   1.1 /  2.4
    • A-20.025-2   –   1.6 /   2.4
    • A-20.025-3   –   1.7 /   2.4
    • A-20.025-4   –   2.1 /   3.2
    • A-20.025-5   –   2.4 /   3.2
    • A-20.025-6   –   3.1 /   4.3
    • A-20.025-7   –   3.3 /   4.3
    • A-20.025-8   –   4.6 /   6.0
    • A-20.025-9   –   4.9 /   6.0
    • A-20.025-10   –   6.1 /   7.9
    • A-20.025-11   –   6.5 /   7.9
    • A-20.025-12   –   Blind /  7.9
    • A-20.025-13   –   5.6 /   6.5
    • A-20.025-14   –   7.0 /   7.9
    • A-20.025-15   –   9.0 /   10.0
    • A-20.025-16   –   4.1 /   6.0

  • Grommet

    • Application:
    Grommet can be fitted in the entrance hole of the connector to prevent moisture and dirt from entering the connector. Has limited strain relief capabilities.

    Construction:
    • Silicone ring slit for easy mounting over the wire. Will compress on the wire when cover is fitted.

    Temperature rating:
    • Max. 200 °C.

    Order no – Dimension A (mm)
    • A-20.048-1 – 2.5
    • A-20.048-2 – 1.5
    • A-20.048-3 – 4.5

  • Wire Insert

    • Application:
    A set inserts fitted an the entrance hole of the connector will provide a very good strain relief without any ptotruding parts from the connector.

    Construction:
    • Thermoplastic material with a round or oval hole to fit around a specific wire

    Order no.   –   Round/Oval / Dimension A / Dimension B (mm)
    • A-20.076-5   –   R / 3.5
    • A-20.076-24   –   R / 2.0 / 1.5

  • Wire Clamp Bracket

    • Application:
    Wire clamp bracket will provide optimum strain relief. Construction allows a large difference in maximum and minimum wire diameter

    Construction:
    • All stainless steel, incl. stainless steel screws.

    Order no.:
    • A-20.055-1 standard connector fits on all connectors CSP(L), CSJ, CSPH(L), CSJH, CSPQ(L), CSJQ, CSPT(L) and CSJT
    • A-20.055-2 for Connector Standard Ceramic fits on all connectors CSPC(L), CSJC
    • A-20.055-5 Connector Standard Duplex fits on all connectors CSPD(L), CSJD
    • A-20.333 Connector Standard Ultra High-temperature fits on all connectors CSPU(L), CSJU

  • U-Bracket Braze/Crimp, Double attachment 1

    • Application:
    Allows the use of two standard connectors to be fitted on duplex mineral insulated metal sheathed cable or duplex wire.

    Construction:
    • Stainless steel crimp braze/crimp-tube (AISI-SS303 / DIN 1.4305)

    Connector Standard
    Order no.   –   Dimension A (mm)  / Dimension B (mm)
    • A-20.116-1   –   6.1 /   7.9
    • A-20.116-2   –   8.1 /   9.9
    • A-20.116-3   –   6.5 /   7.9

    Connector Standard Ceramic
    Order no.   –   Dimension A (mm)  / Dimension B (mm)
    • A-20.340-1   –   5.1 /   7.9
    • A-20.340-2   –   8.1 /   9.9
    • A-20.340-3   –   6.5 /   7.9

    Connector Standard Three-pin
    Order no.   –   Dimension A (mm)  / Dimension B (mm)
    • A-20.352-1   –   6.1 /   7.9
    • A-20.352-2   –   8.1 /   9.9
    • A-20.352-3   –   6.5 /   7.9

  • U-Bracket Wire Clamp, Double attachment 2

    • Application:
    Allows the use of two standard connectors to be fitted on duplex wire. Construction provides optimum strainrelief and large difference in minimum and maximum diameter.

    Construction:
    • All stainless steel inclusive stainless steel screws.

    Connector Standard
    Order no.:
    • A-20.191 – this bracket fits on all connectors CSP(L), CSJ, CSPH(L), CSJH, CSPU(L) and CSJU.

    Connector Standard Ceramic
    Order no.:
    • A-20.341 – The bracket fits for all connectors CSPC(L), CSJC.

    Connector Standard Three-pin
    Order no.:
    • A-20.352 – The bracket fits on all connectors CSPT(L), CSJT.

  • Tube Adapter

    • Application:
    Can be used to mounted the connector on mineral insulated metal sheathed cable or a tube type thermocouple. Can be used several times if not over tightened.

    Order no.   –   Dimension A (mm) – (inch)

    • A-20.154-1   –   1.7   –   1/16
    • A-20.154-2   –   3.3   –   1/8
    • A-20.154-3   –   4.9   –   3/16
    • A-20.154-4   –   6.5   –   1/4
    • A-20.154-6   –   6.0
    • A-20.154-7   –   9.5   –   3/8

    Also available for Connector Standard Ceramic and Connector Standard Ultra High-temperature, please asked for order no.

  • Protection Boot

    • Application:
    The two flexible silicone rubber boots will cover the connector set snugly and prevent moisture, water and dirt entering the connector.

    Temperature rating:
    • Max. 200 °C.

    Construction:
    • Silicone cover with retention ring prevent disconnection due to vibration. Tapered entrance hole to ensure proper sealing on most cable diameters.

    Order no.:
    • A-20.061-1 – Connector Standard Two-pin
    • A-20.061-2 – Connector Standard Three-pin

  • Locking Clip

    • Application:
    In order to prevent accidential disconnection a locking clip can be used.

    Construction:
    • Stainless steel clip
    • Can be placed without any tools

    Order no.:
    • A-20.269

  • Bending Protection

    • Application:
    Bending protection for thermocouples and wire being used with standars connectors. Prevents mechanical damage uf wires at entrance point of the connector.

    Construction:
    • Silicone rubber insert, tapered entrance hole ensures proper sealing un cable
    • Fits in all standard connectors

    Temperature rating:
    • 200 °C.

    Order no.:
    • A-20.294